ESPAÑOL: PÁGINA 23FRANÇAISE : PAGE 43Double Insulated10" Bench Top Table SawInstructionManualPart No. 912933 - 09-15-03The Model and Serial No. p
10OPERATING CONTROLS AND ADJUSTMENTSSTARTING AND STOPPINGSAWThe “ON/OFF” switch (A) Fig 16, is located on the frontof the saw cabinet. To turn the saw
11ADJUSTING 0 AND 45DEGREE POSITIVE STOPSYour saw is equipped with positive stops for rapid andaccurate positioning of the saw blade at 0 and 45degree
12RIPPING THIN STOCK To adjust the fence, pull up on lever (B) so that the top ofthe rip fence can be removed, and repositioned on therip fence as sho
13MITER GAGE OPERATIONAND ADJUSTMENTSWhen straight cross-cutting (blade set 90 degrees to thetable) the miter gage can be used in either table slot.Wh
14Cross-cutting requires the use of the miter gage to position and guide the work. Place the work against the miter gageand advance both the gage and
15If the ripped work is less than 4 inches wide, a PUSHSTICK should always be used to complete the feed, asshown in Fig. 35. The PUSH STICK can easily
16The dado head set (D) Fig. 40, is assembled to the sawarbor as shown. IMPORTANT: The blade guard andsplitter assembly cannot be used when dadoing an
MAINTENANCECHANGING THE BLADE1. DISCONNECT MACHINE FROMPOWER SOURCE. USE ONLY 10" DIAMETER SAWBLADES RATED FOR 4600 RPM OR HIGHER WITH5/8" A
18SERVICE AND REPAIRSAll quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations,includi
1919PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH
2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation
20NOTES
21NOTES
22PORTER-CABLE LIMITEDONE YEAR WARRANTYPorter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase.
The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE •DELTA S.A.) (Lesmarques suivantes sont des
31. FOR YOUR OWN SAFETY, READ THE INSTRUC-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations, and specific hazard
4ADDITIONAL SAFETY RULES FORTABLE SAWS1. DO NOT OPERATE THIS MACHINE until it isassembled and installed according to theinstructions.2. OBTAIN ADVICE
5FOREWORDThe Porter-Cable Model 3812 is a 10" Bench Top Table Saw. The saw comes with a 26"x20" table surface with a ripfence extension
6CARTON CONTENTSFig. 21234567891. Saw2. Fence3. Table Insert4. Blade Guard and Spreader Assembly5. Blade Wrench (2)6. Miter Gauge7. Anchor Block Shim
7ASSEMBLYBLADE RAISING ANDLOWERING HANDWHEELInsert the 1-3/4" screw (D) Fig. 4, through handle (E).Assemble handle (E) to handwheel (A) by thread
86. NOTE: The anchor block (B) Fig. 6, has beenadjusted at the factory so that the spreader will bealigned with the saw blade which is supplied with t
9RIP FENCE TO SAW TABLE1. The rip fence may be used on the right or left handside of the saw table. Lift locking handle (A) Fig. 12, andposition the f
Commentaires sur ces manuels