Porter-cable 28-475X Manuel d'utilisateur

INSTRUCTION MANUAL14" Wood Cutting Band Saw(Model 28-248)(Model 28-475X)PART NO. 426-02-651-0055 - 06-10-03Copyright © 2003 Delta MachineryTo lea

10TOP PLATE TO STAND1. Place the top plate (A) Fig. 10, on the top of thestand (B).2. Align the six square holes on the top plate (A) Fig.10, with the

11BAND SAW USED WITH A DUSTCOLLECTOR3. If you are going to use your band saw with a dustcollector, attach the dust port as follows:A. Align the four h

126. Align the two holes in the hinge (C) Fig. 19, with thetwo holes in the stand door (D). MAKE SURE THAT THEHINGE OPENING IS POINTING DOWN.7. Insert

13SAW TO STANDTHE BAND SAW IS VERY HEAVY. USE AHELPER WHEN ATTACHING THE SAW TO THESTAND.1. Place the band saw on top of the stand as shown inFig. 23.

14TABLE TO SAW1. Align the two table studs (A) Fig. 27, in the bottom ofthe table, with the two holes in the trunnion assemblies(B). Place table on tr

15BLADE TO SAWTHE 14" BAND SAW USES 93½"LENGTH BLADES.1. Remove the table pin (A) Fig. 31 from the table.2. Open the two wheel guard doors (

16ON / OFF SWITCH TO STAND1. Remove the two outer hex nuts and lock washers (A)Fig. 34 from the two screws extending out from the backof the switch bo

177. Insert the switch cord (H) Fig. 39, through the hole inthe cord bushing (G).8. Insert the pronged motor plug (J) Fig. 40, into thereceptacle (H)

18TILTING THE TABLE1. The table on the band saw can be tilted 45 degreesto the right and 8 degrees to the left. To tilt the table tothe right, loosen

19Fig. 47To set the adjustable stops:1. Loosen the two clamp handles (A) Fig. 43.2. Tilt the table to the right, and turn the stop untileither stop sc

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

20Fig. 515. The band saw blade tension can be fined tune byturning adjustment nut (N) Fig. 51, while the blade istensioned.6. A series of graduations

21ADJUSTING THE UPPERBLADE GUIDES AND BLADESUPPORT BEARINGAdjust the upper blade guides and blade supportbearings ONLY AFTER the blade has the correct

22ADJUSTING LOWER BLADEGUIDES AND BLADE SUPPORTBEARINGAdjust the lower blade guides and blade support bearingafter the upper guides and bearing have b

23TROUBLESHOOTING GUIDE(continued on next page)Trouble: SAW WILL NOT START.Probable Cause Remedy1. Switch cord / motor cord not plugged in. 1. Plug i

24Trouble: BLADE WILL NOT TRACK.Probable Cause Remedy1. Blade too loose 1. Adjust tension2. Upper wheel not properly adjusted. 2. Adjust upper wheel.3

25BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You canobtain long use from a band saw blade if

26NOTES

27PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

31. FOR YOUR OWN SAFETY, READ THE INSTRUCT-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations, and specific hazar

4FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SAFETY RULESFOR BAND SAWSSAVE THESE INSTRUCTIONS. Refer to them often

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

6Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding type plug

7UNPACKING AND CLEANINGCarefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainte

8BAND SAW PARTSFig. 4 Fig. 512345689101112131415161718192021222324252627281. Saw2. Stand3. Dust Chute4. Top Plate5. Stand Door6. Motor and key (A)7. T

9ASSEMBLYFOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE