Porter-cable 3700L Manuel d'utilisateur

ESPAÑOL: PÁGINA 23FRANÇAISE : PAGE 4510" Compound Laser Miter SawInstructionManualPart No. A05636 - 08-06-04The Model and Serial No. plate is loc

10To start the machine, depress the switch trigger (A) Fig. 13. To stop the machine, release the switch trigger.This saw is equipped with an automatic

To adjust the sliding fit between the movable table and the base,turn the nut (A) Fig. 17 clockwise to increase the sliding fit(opposite to decrease t

12TILTING CUTTINGHEAD FOR BEVEL CUTTINGDISCONNECT THE MACHINE FROM THE POWER SOURCE.IMPORTANT: Move the sliding fence to provide clearance for the bla

131. Adjust the saw so that both the bevel and miter pointers are set at 0°. Tighten the bevel lock handle (A) Fig. 25 and lockthe cuttinghead in the

ADJUSTING THE TwinLaser™LINESEach of the laser lines have been aligned parallel to the blade at the factory and should not need any adjustment priorto

VERTICALALIGNMENTSET SCREWS15PARTIALCUTBRASSHEXNUTLAFig. B2Fig. CThe rotation of the lines is set parallel at the factory and permanently secured. No

161. Carefully clean sawdust from each laser lens (A) Fig. J witha cotton swab (B). Do not use solvents of any kind sincethey may damage the lens. Avo

17AUXILIARY WOOD FENCEWhen performing multiple or repetitiveoperations that result in small cut-off pieces (one inch orless), the saw blade can catch

18For support when cutting long pieces, construct a worksupport extension. Fig. 39 illustrates the miter saw mountedon two standard 2 x 4’s (A). Faste

19CUTTING CROWN MOULDINGOne of the many features of the saw is the ease of cuttingcrown moulding. The following is an example of cuttingboth inside an

2TABLE OF CONTENTSIMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2020MAINTENANCECHANGING THE BLADEUse only cross-cutting saw blades.When using carbide-tipped blades, donot use blades with deep gullets asthey can def

21KEEP TOOL CLEANPeriodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth.NEVER use

2222PORTER-CABLE LIMITEDONE YEAR WARRANTYPorter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchas

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.1. DO NOT OPERATE THIS MACHINE UNTIL it isassembled and installed according to th

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

7EXTENSION CORDSUse proper extension cords. Make sureyour extension cord is in good condition and is a 3-wireextension cord which has a 3-prong ground

8MOVING THE CUTTINGHEAD TO THE UP POSITION1. Pull out the cuttinghead lockpin (A) Fig. 1, and move the cuttinghead (B) to the up position.2. Fig. 2 sh

91. Thread the two M8 x 1.25 x 20 Hex Head Screwinto the holes (A) Fig. 4 on the left side of the saw.NOTE: Loosely tighten the hardware for further a